Workshop Repair and Service Manuals GMC SIERRA
Articles

Body

Plastic Identification and Refinishing Systems      Plastic Identification and Refinishing Systems Identifying Symbol– Old Symbol in ( )s Chemical Composition or Plastic Family Name Typical Area(s) Where Part is Used Examples of Common / Trade Names Type of Plastic...
Flexible Plastic Part Repair Materials      Product– 88861039, *88861040, High Strength PlasticRepair 50-ml Components– 12 cartridges with 2 mixers each Structural and Cosmetic Recommended Repair Material Product Components Recommended Repair Material Work Time...
Eliminating Unwanted Odors in Vehicles      GM Vehicle Care Odor Eliminator,GM-P/N-88861431(Canadian-P/N-88861436), may control oreliminate odors in the interior and luggage compartment areas of GMvehicles. This non-toxic, biodegradable, odorless product has beenshown...
Rigid Plastic Part Repair Materials      Rigid Plastic Part Repair Materials Thermoset Plastic Type Type of Repair Recommended Repair Material Availability Sheet metal compound (SMC), RIM rigid plastic parts Cosmetic filling GM Goodwrench® Structural...
General Plastic Repair      Warning:In order to reduce the risk of personal injury when exposedto toxic fumes while grinding, cutting, or applying repair materialon any type of sheet molded compound or RIM rigid plastic, observethe following guidelines:...
Transmission Fluid Pump Body Disassemble      Remove the pump slide outer spring-(245).Place a rag over the spring while removing to prevent thespring from flying out. Remove the oil pump rotor-(212) and pump vanerings-(210).Remove the pump vanes-(213).Remove the...
Rear Seat Removal and Installation (Heavy Duty Crew Cab with A68)      Rear Seat Removal and Installation Callout Component Name 1 Rear Seat Assembly Nut (Qty:-8) Caution:Refer toFastener Caution. Procedure Remove nut and slide seat belt webbing through the rear seat and out of...
Plastic Collar Quick Connect Fitting Service      Disconnect Procedure Warning:Refer toGasoline/Gasoline Vapors Warning Note:There are several types of Plastic Collar Fuel andEvaporative Emission Quick Connect Fittings used on thisvehicle. Bartholomew (1)Q Release...
Plastic Collar Quick Connect Fitting Service      Removal Procedure Warning:Refer toGasoline/Gasoline Vapors Warning. Note:There are several types of Plastic Collar Fuel andEvaporative Emission Quick Connect Fittings used on thisvehicle. Bartholomew-(1)Q...
PIT3098D Diagnostic Tips Vehicle Body Tilt Or Lean - (Sep 11 2012)      Subject: Diagnostic Tips: Vehicle Body Tilt Or Lean Models:  1999 - 2006 Cadillac Escalade Models 1999 - 2006 Chevrolet Avalanche, Suburban, Tahoe 2007 - 2013 Chevrolet Suburban HD 1999 - 2007 Chevrolet...
PIT3098D Diagnostic Tips Vehicle Body Tilt Or Lean - (Sep 11 2012) - part 2      If this is not possible, check front eye of rear leaf springfor matching color-coded tape or paint. Both sides should be the same color. If not,switch springs side to side. If so, replace leaf spring on lower side only.Recheck...
Oil Pump Cover and Body Assemble      Special Tools J-21368Pump Body and Cover Alignment Band Place the oil pump cover onto the oil pump body and putstator shaft through a hole in the bench.Install the pump cover bolts (233) finger tight only. Install...
Oil Pump Body Bushing Replacement      Special ToolsJ-41778-1Pump Body Bushing Installer/RemoverJ-41778-2Pump Body Bushing Position Stop Inspect the oil pump body for the following:Worn or damaged bushingsForeign material or debrisPorosityScored or irregular...
Oil Pump Body Bushing Replacement      Tools RequiredGE-8092 Driver HandleJ 43771 Pump Bushing Removal and Installation Tool Inspect the bushing for damage and wear. The bushing must not be damaged or worn.Measure the ID of the bushing. Replace the pump bushing...
Oil Pump Body Assemble      Special ToolsJ-25016Pump Seal and Speedometer Gear InstallerJ-36850Transjel Lubricant Using theJ-25016gear installer-(1), install the oil sealassembly-(243). Install the fluid seal retainer-(244). Install an O-ring...
How to Identify Plastic Parts      sae pvc sae Plastic parts can be identified by the SAE code, which isusually found on the rear of the part, and/or by thecharacteristics of the plastic. Knowing the type of plastic aids inselecting the proper repair...
Fuel Injector Fuel Meter Body Replacement      Removal Procedure Note:An 8-digit part identification number is on a mylar labelaffixed to the fuel meter body. Refer to this number if servicingor part replacement is required. Remove the upper intake manifold. Refer...
Control Valve Upper Body Replacement      Removal ProcedureRemove the control solenoid valve and transmission controlmodule assembly. Refer toControl Solenoid Valve and Transmission Control Module Assembly Replacement. Remove the manual shift detent...
Control Valve Upper Body Assembly Cleaning and Inspection      Control Valve Upper Body Assembly Cleaning and Inspection Callout Component Name Warning:Valve springs can be tightly compressed. Use care whenremoving retainers and plugs. Personal injury could result. Caution:Do...
Control Valve Lower Body Assembly Cleaning and Inspection      Control Valve Lower Body Assembly Cleaning and Inspection Callout Component Name Warning:Valve springs can be tightly compressed. Use care whenremoving retainers and plugs. Personal injury could result....
Control Valve Lower Body and Upper Body Replacement      Control Valve Lower Body and Upper Body Replacement Callout Component Name Preliminary Procedures Remove the transmission electrical connector. Refer toAutomatic Transmission Electrical Connector Passage Sleeve...
Body Wiring Harness Junction Block Replacement      Body Wiring Harness Junction Block Replacement Callout Component Name 1 Body Harness Junction Block ProcedureRemove the cover.Disconnect the electrical connectors.
Body Waterleak Repair      Warning:If the vehicle interior is exposed to moisture and becomessoaked up to the level of the sensing and diagnostic module (SDM),the SDM and SDM harness connector must be replaced. The SDM couldbe activated when powered,...
08-08-51-002A Pre-Painting Cleaning Process for TPO Plastic Fascias - (Jan 16 2013)      Subject: Pre-Painting/Cleaning Process for TPO Plastic Fascias Models:  2013 and Prior GM Passenger Cars and Trucks     This bulletin is being revised to clarify Subject and add the 2010-2013 model...