Workshop Repair and Service Manuals GMC SIERRA
Articles

09-06-04-026G Identifying Non-GM (Aftermarket) Engine and Transmission Calibrations for V6 and V8 Gasoline Engines Using Tech 2 or Global Diagnostic System 2 (GDS 2) - (Mar 19 2013) - part 8

Rating:
The Calibrations Group will also update the PQCor TAC case with the results of the Calibration Verification Request.

Be prepared to provide all the usual documentation that is normally required whenrequesting an assembly authorization from the PQC.

Notice:DO NOT contact GM Technical Assistance (TAC) to discuss warranty concerns on theaftermarket calibrations. ALL questions and concerns about warranty should be directedto the District Manager Aftersales (DMA), in Canada the DM-CCSP (District Manager-CustomerCare and Service Process).

11. Calibrations Group - New E-mail Address - TACCVN@gmexpert.com

The Calibrations Group has a new e-mail address to be used when mailing the digital.jpg photographs of the Engine Calibration ID and Verification No. (Number) Informationtaken from the Tech 2® or JPEG photographs from the GDS 2 Calibration History screenshot.

E-mail all .jpg or JPEG files to this address: TACCVN@gmexpert.com

12. Warranty InformationThe Dealership Service Management must be involved in any situation that would justifythe use of labor operation 0600014.Notify the District Manager Aftersales (DMA), in Canada the DM-CCSP (District Manager-CustomerCare and Service Process) of the situation.All claims will have to be routed to the Warranty Support Center (WSC) for approval.Please refer to Corporate Bulletin Number 09-00-89-016, Labor Operation 0600014 -Suspected Tampering or Vehicle Modifications for important information.

For vehicles repaired under warranty, use:

Labor Operation

Description

Labor Time

0600014

Suspected Tampering or Vehicle Modifications

0.2-hr

GM bulletins are intended for use by professional technicians,NOT a "do-it-yourselfer".  They are written to inform thesetechnicians of conditions that may occur on some vehicles, or toprovide information that could assist in the proper service of avehicle.  Properly trained technicians have the equipment,tools, safety instructions, and know-how to do a job properly andsafely.  If a condition is described, DO NOT assume that thebulletin applies to your vehicle, or that your vehicle will havethat condition.  See your GM dealer for information on whetheryour vehicle may benefit from the information.

#09-06-04-026G: Identifying Non-GM (Aftermarket) Engine and Transmission Calibrations for V6 and V8 Gasoline Engines Using Tech 2 or Global Diagnostic System 2 (GDS 2) - (Mar 19, 2013)

WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION

Camshaft Position Actuator and Solenoid Valve Description Valvetrain Camshaft - part 2     Duringnormal engine operation, and based on performance requirements, theECM may adjust camshaft timing, as required, within a range from7-degrees advanced to 45-degreesretard. CMP System Lubrication Flow and Actuator Operation...
PIE0273 Engineering Information - Engine Oil Leak at Lower Oil Pan - (Nov 6 2013) Engine Lubrication Oil Sump Pan     Subject: Engineering Information – Engine Oil Leak at Lower Oil Pan Models:  2013 Chevrolet Express, Silverado 2013 GMC Savana, Sierra Equipped with 6.6L Duramax® Diesel Engine (RPO LGH or LML) Attention:...
Oil Level Indicator and Tube Installation Engine Lubrication Oil Level Indicator Tube     Apply sealant GM-P/N-12346004(Canadian-P/N-10953480) or equivalent, aroundthe oil level indicator tube 13-mm (0.5-in)below the tube bead.Install the oil level indicator tube into the engine block.Rotate the oil level...
Engine Replacement     Special Tools J-41427 Engine Lift Brackets Removal Procedure Raise the hood to the service position, perform the following:Remove the hood hinge bolts (1).Raise the hood until vertical.Install the hood hinge bolts until...
Oil Pump Suction Pipe and Screen Assembly Installation Engine Lubrication Oil Pump     Install the NEW oil pump pipe and screenseal-(1).Install the oil pump pipe and screen-(2). Caution:Refer toFastener Caution. Install the oil pump pipe and screen assemblybolts-(3) and (4) and tighten to25-Y(18-lb-ft).
Fastener Tightening Specifications - 4WD Driveline Control Engine Cooling     Fastener Tightening Specifications Application Specification Metric English Air Cleaner Outlet Duct Clamp 4-Y 35-lb-in Coolant Air Bleed Pipe Bolts 12-Y 106-lb-in Coolant Heater 50-Y...