Workshop Repair and Service Manuals GMC SIERRA
Articles

1-2-3-4-5-6 Clutch Piston Housing Assemble Automatic - part 2

Rating:

Position the 1–2–3–4, 4–5–6 clutch housing-(6) on the base of J 24204-2 assembly-(7) so that the rear of the housing is facing up.Install J 47339-1 compressor-(4) onto the shaft of J 24204-2 assembly-(7).Center J 47339-1 compressor-(4) on the 1–2–3–4 clutch balance piston.Install the J 24204-2 assembly ball bearing-(3) and washer-(2) onto the shaft of J 24204-2 assembly.Install the J 24204-2 assembly wing nut-(1) on the shaft of J 24204-2 assembly.Compress the 1–2–3–4 clutch piston return spring assembly until the retaining ringgroove on the 1–2–3–4 clutch housing is visible.Install the retaining ring-(5) into the 1–2–3–4 clutch housing.Remove all of the J-tools.

1-2-3-4-5-6 Clutch Piston Housing Assemble Automatic

Install 2 overlap seal rings-(4) onto the turbine shaft-(3).Position the turbine shaft-(3) on the work table so that the rear of the shaft isfacing up.Align the 1–2–3–4, 4–5–6 clutch housing-(2) with the rear of the turbine shaft-(3)so that the rear of the clutch housing is facing up.Install the 1–2–3–4, 4–5–6 clutch housing-(2) onto the rear of turbine shaft-(3).Install the retaining ring-(1) onto the turbine shaft-(3).Make sure the retaining ring-(1) is seated completely around the turbine shaft-(3).

1-2-3-4-5-6 Clutch Piston Housing Assemble Automatic

Starting with a 1–2–3–4 clutch steel plate, alternately install seven 1–2–3–4 clutchsteel plates-(2) and seven 1–2–3–4 clutch fiber plates-(1) onto the turbine shaft-(3).

1-2-3-4-5-6 Clutch Piston Housing Assemble Automatic

Note:Do not use the pressure plate and selector tool from the J 44525 selector set if they are not matched in color. Special tools J-44525-4 selector tool-(4) andJ-44525-5 pressure plate-(3) are silver plated for easy identification. Only use thesilver plated tools in this procedure.

Align J-44525-5-pressure plate-(3) with the turbine shaft so that the countersunkholes of J-44525-5-pressure plate-(3) are facing up.Install J-44525-5-pressure plate-(3) onto the turbine shaft.Align J-44525-1-compressor-(2) with the turbine shaft so that the inner ridge of J-44525-1-compressor-(2)is facing down.Slide the inner ridge of J-44525-1-compressor-(2) into the turbine shaft retainingring groove.Align the holes in J-44525-1-compressor-(2) with the countersunk holes of J-44525-5-pressureplate-(3).Hand install 2-bolts-(1) of J 44525 selector into the holes of J-44525-1-compressor-(2). Tighten the bolts to 1.8-Y (16-lb-in).

1-2-3-4-5-6 Clutch Piston Housing Assemble Automatic

Note:The shift quality of the transmission depends heavily upon selecting the correct 1–2–3–4clutch backing plate.

Perform the following procedure for each tab of J-44525-4-selector tool-(1):Place the flat surface, tabbed end of J-44525-4-selector tool-(1) onto the top surfaceof J-44525-5-pressure plate-(2).

Note:At most, 2-of the different tabs will fit into the retaining ring groove.

Try to slide the tabbed end of J-44525-4-selector tool-(1) into the retaining ringgroove on the turbine shaft.If a tab fits into the retaining ring groove, record the 4-digit ID number locatedon the tab of J-44525-4-selector tool-(1). Refer toSelective Components Specificationsto determine the correct backing plate.Select a 1–2–3–4 clutch backing plate as follows:If no tab of J-44525-4-selector tool-(1) fits into the retaining ring groove, selectthe 1–2–3–4 clutch backing plate with ID-No.-2420.If one or more tabs of J-44525-4-selector tool-(1) fit into the retaining ring groove,select the 1–2–3–4 clutch backing plate with an ID-No.
Differential Drive Pinion Gear Yoke Replacement Automatic     Removal Procedure Place the transmission in the Park-(P) selector position. Warning:Apply the parking brake and block the drive wheels beforeperforming this procedure in order to prevent bodily injury. Apply the parking...
Temperature Versus Resistance (Transmission Fluid Temperature Sensor) Automatic     Temperature Versus Resistance Temperature Temperature Minimum Resistance Nominal Resistance Maximum Resistance °C °F ? ? ? ?45 ?49 128565 141951 155338 ?40 ?40 95826 100735 105644...
Transmission Replacement Automatic Transmission Unit - part 2     Remove the transmission electrical harness retaining bolt-(1).Disconnect the transmission electrical harness connector-(7) from the vehicle speedsensor-(5).Disconnect the transmission electrical harness connector-(4) from the...
Manual Shift Shaft Seal Replacement Automatic     Tools RequiredJ 43911 Manual Shift Shaft Seal RemoverJ 43909 Manual Shift Shaft Seal InstallerRemoval Procedure Be sure that the jackscrew for J 43911 manual shift shaft seal remover is backed off and will not interfere...
Transmission Front Case Disassemble Manual     Using a 13-mm wrench, remove the7-screws from the bearing retainer. Using a screwdriver, remove the gear train cup. Remove the gear train adjustment shims. Remove the gear train spacer. Using a punch and a...
PIP5059 Whistle Or Whine Noise In 3rd Gear May Be More Pronounced On A Coast - (Sep 6 2012)     Subject: Whistle Or Whine Noise In 3rd Gear May Be More Pronounced On A Coast Models:  2010 - 2013 Chevrolet Colorado, Express, Silverado 2010 - 2013 GMC Canyon, Savana, Sierra Equipped with 4L60E (M30)...